Methodology

Every number on this site can be traced to a document published by the water utility. This page explains what we collect, how we convert it, and where the limits are.

1. Sources we accept

In order of preference:

  • Consumer Confidence Reports (CCRs). These are the annual drinking water quality reports US community water systems must publish under the Safe Drinking Water Act. Hardness isn't a regulated contaminant, so not every CCR includes it. Many list it under "secondary" or "additional" parameters.
  • Official utility pages and monthly data sheets. Some cities publish hardness on a water quality FAQ or post monthly treatment-plant averages.
  • USGS Water Quality Portal and EPA SDWIS are used for context and system identifiers. We don't use regional estimates or modelled values as a city's headline figure.

For each city we record the publisher, document title, URL, reporting period, the exact line the figure came from and the date we accessed it. If we can't find a published figure, we don't publish a page. We would rather leave a city out than show a guessed number.

2. Averages, ranges and typical values

Utilities report hardness in different ways, and we label which one you're looking at:

  • Annual or monthly average: used as the headline figure.
  • Range only: we show the full range and use its midpoint for the headline and the classification, labelled as a midpoint. Softener sizing uses the top of the range.
  • Typical value: a figure the utility states without a reporting period, for example on an FAQ page. We note that it is undated and show when we last checked it.

Where a utility publishes conflicting figures (an average in the text that differs from the data table, for instance), we use the table value and show the other figure on the city page.

3. Units and conversion

Hardness is reported as milligrams per liter (mg/L) of calcium carbonate (CaCO₃). One mg/L equals one part per million (ppm). Softener makers use grains per US gallon:

1 gpg = 17.1 mg/L as CaCO₃. So gpg = mg/L ÷ 17.1. One grain is 1/7000 of a pound. We also show German degrees (°dH) for dishwasher settings: 1 °dH ≈ 17.8 mg/L.

The hardness unit converter also handles French and English degrees, mmol/L, and total hardness from separate calcium and magnesium results (2.497 × Ca + 4.118 × Mg, Standard Methods 2340 B).

When a utility publishes its own gpg value, we show it in the source quote. Our displayed gpg is always our own conversion of the mg/L figure, so every city is converted the same way.

4. Classification

We use the U.S. Geological Survey bands: soft 0–60 mg/L, moderately hard 61–120, hard 121–180, very hard over 180. Some utilities use their own scales. When they do, we mention it on the city page, but the badge always follows USGS.

5. Softener sizing and salt

  • Daily load = hardness (gpg) × people × 75 gallons per person per day, the figure in Penn State Extension's sizing example. The calculator accepts 20 to 200 gallons.
  • Iron compensation, where entered: +4 gpg per 1 ppm of clear-water iron by default. The Water Quality Association gives a factor of typically 3, and 2, 4 or 5 in some guidance; the calculator lets you choose 3, 4 or 5.
  • Target one regeneration roughly every 7 days (adjustable from 3 to 14).
  • A salt-efficient setting is assumed to deliver ⅔ of a unit's rated capacity, from resin capacity of about 20,000 grains per ft³ at 6 lb of salt against 30,000 at 15 lb. Required rated capacity = daily load × days ÷ ⅔, rounded up to the next common size: 24,000, 32,000, 40,000, 48,000, 64,000, 80,000, 96,000 or 110,000 grains.
  • Salt per year = daily load × 365 ÷ grains removed per pound of salt: 3,350 for an NSF/ANSI 44 efficiency-rated softener, 4,000 for California efficiency, 3,333 or 2,000 for resin at 6 or 15 lb per ft³.

These are planning figures. Valve type, resin volume and salt dose vary between models, so check the manufacturer's capacity table at the salt setting you plan to use. The calculators show the working and list every source.

6. Limits of the data

  • Figures describe the public water system, not your tap. Blending of sources, seasonal changes, building plumbing and any treatment in your home all change what comes out of your faucet.
  • Private wells are not covered.
  • ZIP codes are matched by postal city name using the GeoNames postal code dataset (CC BY 4.0). A ZIP can be served by more than one utility, and utility boundaries rarely follow ZIP lines.
  • Hardness is not a health measure. We don't make drinking-water safety claims. For those, read your utility's full CCR or contact your state drinking water program.

7. Updates and corrections

Each city page shows the date we last checked its source. When a utility publishes a new annual report, we update the figure and the date. If you spot an outdated or wrong number, send us the link and we'll correct it.