Water softener salt and cost calculator

How much salt will a softener use at your hardness, and what does it cost a year? The answer depends heavily on how efficiently the softener is set to use salt, so this calculator shows every common setting side by side.

People in the home
4
If the manual gives capacity and salt per regeneration, efficiency = capacity ÷ pounds of salt.
$7.00 is only a placeholder. Type what your store charges.
Salt per year
–
Bags per year–
Salt cost per year–
Salt per month–
Hardness removed per year–
Regeneration water, efficiency-rated unit–

Minimum salt for a metered softener that regenerates only when the resin is spent. A time-clock unit that regenerates on a fixed schedule uses more. How this works.

Same household, every salt setting

Salt efficiencylb / yearBags / yearCost / year

How the estimate works

1. Grains to remove per day = hardness in gpg (plus 4 gpg per ppm of iron) × people × gallons per person. It is the same daily load as the sizing calculator.

2. Grains per year = daily load × 365.

3. Pounds of salt = grains per year ÷ the grains the softener removes per pound of salt.

4. Bags and cost = pounds ÷ bag size, × the price you enter.

Step 3 is the one that matters. The same water and the same family can need twice as much salt depending on the setting, because resin gives diminishing returns. One cubic foot regenerated with 6 lb of salt removes about 20,000 grains, or 3,333 per pound. Pushing it to 15 lb only raises that to 30,000 grains, or 2,000 per pound.

Where the efficiency figures come from

  • 3,350 grains per lb is the minimum for an efficiency-rated softener under NSF/ANSI 44, the U.S. standard for residential softeners. Look for “Efficiency Rated” on the NSF listing or the data plate.
  • 4,000 grains per lb is the higher bar for softeners rated for sale in California.
  • 3,333 and 2,000 grains per lb come from the resin capacity a softener maker publishes at 6 lb and 15 lb of salt per cubic foot.

Only demand-initiated softeners, with a meter or sensor, can be efficiency rated. A time-clock softener regenerates on schedule whether the resin needs it or not, so its real salt use is higher than any figure here.

The water used to regenerate

An efficiency-rated softener may use no more than 5 gallons of regeneration water per 1,000 grains removed, so the last line in the result is a ceiling for a certified unit. Older or time-clock units can use more.

Worked example

Four people, 75 gallons each, 10 gpg, no iron: 10 × 4 × 75 = 3,000 grains a day, or 1,095,000 grains a year. An efficiency-rated softener (3,350 grains per lb) needs 1,095,000 ÷ 3,350 = 327 lb of salt a year, about 8.2 forty-pound bags. Run at full salt (2,000 grains per lb), the same household uses 547.5 lb, about 13.7 bags. The difference is about five and a half bags a year, every year the softener runs.

To check what your current unit does, find its rated capacity and salt dose per regeneration in the manual and divide one by the other. A “32,000-grain” unit that uses 16 lb a regeneration is running at 2,000 grains per lb.

Sources

Each constant in this calculator comes from one of these documents. We checked them on November 19, 2026.

  1. Marlo Inc. (softener manufacturer), “MGT Series Water Softeners brochure, capacity footnote”. What we use: Maximum capacity 30,000 grains per ft³ of resin regenerated with 15 lb of salt; minimum 20,000 grains per ft³ with 6 lb. That ratio is our ⅔ “salt-efficient” factor, and it gives 2,000 and about 3,333 grains removed per lb of salt.
  2. NSF, “NSF/ANSI 44 Cation Exchange Water Softeners: certified product listings, efficiency-rating note”. What we use: An efficiency-rated [ER] softener removes at least 3,350 grains of hardness per lb of salt and uses 5 gallons or less of regeneration water per 1,000 grains removed.
  3. U.S. Department of Energy, Building America Solution Center (PNNL), “Water Softeners”. What we use: The same NSF/ANSI 44 efficiency criteria, and that only demand-initiated (metered or sensor) softeners can be efficiency rated; time-clock units regenerate on a schedule whether or not the resin is spent.
  4. NSF International, in WaterWorld, “Water Softening: Evaluating Efficiency”. What we use: Softeners rated for use in California must reach at least 4,000 grains per lb of salt.
  5. Penn State Extension, “Water Softening (Robillard, Sharpe and Swistock; updated September 8, 2025)”. What we use: 1 gpg ≈ 17 mg/L; the five-step gpg hardness scale (Table 1); the sizing example 75 gal × 10 gpg × 4 people = 3,000 grains a day, so a 20,000-grain unit regenerates about every 6–7 days; below 7 gpg scale and soap film are usually minor; oxidized (red) iron fouls resin.
  6. Nelsen Corporation (water treatment equipment distributor), “Softener Sizing Calculator: method notes”. What we use: Compensated hardness = gpg + 4 × iron ppm; 75 gal per person per day; most softeners are rated for up to 2 ppm of ferrous iron.
  7. U.S. EPA WaterSense, “Statistics and Facts”. What we use: Each American uses an average of 82 gallons of water a day at home (citing USGS water-use estimates for 2015).

The calculator runs in your browser. Nothing you type is sent to us or stored. Found an error? Tell us and we'll correct it.

Other calculators