Is my water hard?
Type the number from your test strip, lab result or utility report. You'll see where it sits on the two scales used in the US, what that usually means for scale and soap, and which cities in our directory have similar water.
USGS scale
| Class | mg/L | gpg |
|---|---|---|
| Soft | 0–60 | 0–3.5 |
| Moderately hard | 61–120 | 3.6–7.0 |
| Hard | 121–180 | 7.1–10.5 |
| Very hard | over 180 | over 10.5 |
Penn State Extension scale
| Class | gpg | mg/L |
|---|---|---|
| Soft | under 1.0 | under 17 |
| Slightly hard | 1.0–3.5 | 17–60 |
| Moderately hard | 3.5–7.0 | 60–120 |
| Hard | 7.0–10.5 | 120–180 |
| Very hard | over 10.5 | over 180 |
Cities in our directory with similar water
Closest utility-reported figures to your reading. Each city page cites the utility's own report.
Why there are two scales
The U.S. Geological Survey splits hardness into four bands in mg/L: soft up to 60, moderately hard to 120, hard to 180 and very hard above that. It is the scale on every city page of this site.
Penn State Extension, like much of the softener industry, works in grains per gallon and adds a fifth band. Anything under 1 gpg (17 mg/L) is soft, and 1 to 3.5 gpg is only “slightly hard”. The upper boundaries line up with USGS: 3.5 gpg is 60 mg/L, 7 gpg is 120 and 10.5 gpg is 180.
So the two only disagree at the bottom. Water at 40 mg/L is soft to the USGS and slightly hard to Penn State, and neither would suggest doing anything about it.
What the bands mean in practice
Hardness is not a health measure. It is about scale, soap and appliances. Penn State's rule of thumb is that water below about 7 gpg (120 mg/L) will probably not cause major scaling or soap film. Above that, deposits in water heaters and kettles and spots on glass become more noticeable. Even then, Penn State calls softening a matter of personal preference, not necessity.
Test strips are read by matching colors, so treat a strip result as approximate. If the result will decide whether you spend money on a softener, compare it with your utility's published figure or a lab test before you buy.
Next steps: size a softener, estimate the salt, or look up your city.
Sources
Each constant in this calculator comes from one of these documents. We checked them on November 19, 2026.
- U.S. Geological Survey, Water Science School, “Hardness of Water”. What we use: The four bands in mg/L as CaCO₃: 0–60 soft, 61–120 moderately hard, 121–180 hard, over 180 very hard.
- Penn State Extension, “Water Softening (Robillard, Sharpe and Swistock; updated September 8, 2025)”. What we use: 1 gpg ≈ 17 mg/L; the five-step gpg hardness scale (Table 1); the sizing example 75 gal × 10 gpg × 4 people = 3,000 grains a day, so a 20,000-grain unit regenerates about every 6–7 days; below 7 gpg scale and soap film are usually minor; oxidized (red) iron fouls resin.
- University of Bayreuth, Chemistry Education, “Wasser-Härte (teaching unit on water hardness, in German)”. What we use: 1 °dH = 10 mg/L CaO = 17.8 mg/L CaCO₃; German consumer hardness ranges: soft under 8.4 °dH, medium 8.4–14 °dH, hard over 14 °dH.
- NIST, “Guide for the Use of the International System of Units (SP 811), Appendix B.8: conversion factors”. What we use: 1 grain = 64.79891 mg; 1 US gallon = 3.785412 L; 1 UK gallon = 4.54609 L. So 1 grain per US gallon = 17.118 mg/L, and 1 grain per UK gallon (the English or Clark degree) = 14.254 mg/L.
The calculator runs in your browser. Nothing you type is sent to us or stored. Found an error? Tell us and we'll correct it.
Other calculators
Water softener size calculator
Grains per day, the rated capacity to buy and how often it will regenerate. Handles iron, salt setting and a unit you already own.
Open →Softener salt and cost calculator
Pounds of salt, bags and dollars a year for your hardness and household, and how much an efficient setting saves.
Open →Hardness unit converter
mg/L, ppm, grains per gallon, German, French and English degrees and mmol/L, plus hardness from a calcium and magnesium lab result.
Open →